Pressure equipment integrity · Process safety
Inspect.Detect.Correct.
Independent inspection and process safety for boilers, pressure vessels, piping and tanks in British Columbia and Alberta. Forty years in the boiler room, applied to your plant. One accountable lead, and a team sized to the job.
The method
Three steps. One inspector who owns all three.
Most inspection reports stop at the finding. Ours carry through to the damage mechanism, the program gap behind it, and the repair that closes it. Select a step.
Services
Nine ways we show up on site
Each engagement is scoped to your equipment, your jurisdiction and the codes it is registered under. Open any line for what is included.
Bench strength
One accountable lead. A team sized to the job.
A one-day second opinion is done by Robert himself. An outage inspection program, a stamped repair, or a failure investigation with lab work is staffed from the specialists TIMI works with, under TIMI’s lead and with TIMI’s name on the report. You deal with one person, and that person is accountable for the result.
- P.EngProfessional engineeringStamped repairs, alterations and re-rates; fitness-for-service and remaining life calculations that need a seal
- NDENon-destructive examinationCertified UT, MT, PT and RT technicians, from a single thickness survey to a full outage scope
- InspectInspection crewsAPI 510 / 570 / 653 inspectors and ABSA in-service inspectors to crew an outage, with TIMI setting the scope and signing off
- RepairWelding and repair contractorsOrganizations holding ABSA certificates of authorization and Technical Safety BC contractor licences, with the paperwork checked before the first arc
- LabMetallurgy and chemistryFailure analysis, deposit analysis and water chemistry for the cases a visual inspection cannot settle
- ControlsInstrumentation and controlsDCS, combustion control and alarm specialists for tuning, firing-rate trials and alarm rationalization
Jurisdiction
Which code governs your equipment?
Pick the equipment and the province. The table shows the construction code, the in-service inspection standard, the repair and alteration rules, and who regulates it.
General guidance. The governing document for a specific unit depends on its registration, service, and the owner-user program it sits under. Confirming that is usually the first hour of an engagement.
Credentials
Certified where it counts, on both sides of the Rockies
Current certifications
- PowerFirst Class Power EngineerCertified in British Columbia and Alberta
- APIAPI 510 Pressure Vessel InspectorCurrent authorization
- ABSAIn-Service Boiler and Pressure Vessel InspectorAlberta Boilers Safety Association
- IRLevel 1 ThermographerCasing, refractory and insulation surveys while the unit runs
- EnergyCertified Energy Manager, Certified Energy AuditorCEM and CEA, maintained
Industries
- Pulp and paper: kraft recovery boilers, power boilers, mill steam plants
- Natural gas processing plants
- Oil sands and SAGD facilities
- Food processing steam plants
- Industrial boiler houses of every size
Working references
- ASME BPVC Sections I, II, IV, V, VIII, IX, X and XIII as referenced by CSA B51:24
- CSA B51:24 and the TSBC regulation schedule in force since December 31, 2024
- API 510, API 570, API 653 and NB-23 (NBIC), current editions
- NFPA 85 for combustion safeguards
- ABSA AB-506, AB-512 and AB-513
About
Four decades around steam, most of them inside the boiler
Robert Vesak has worked around boilers since 1978, starting in the steam plant at Ocean Falls. The equipment has changed and the code books have thickened, but the job is the same: know what the metal is doing before it tells you.
He is a First Class Power Engineer certified in BC and Alberta, a current API 510 inspector and an ABSA-certified in-service boiler and pressure vessel inspector, and has held a National Board commission. His background runs through BC pulp and paper into gas processing, oil sands and food processing.
Trust Integrity Management Inc. is his firm, based in Clearwater, BC. He leads every engagement himself and brings in the engineers, inspectors and specialists the scope calls for. Recent work includes a remaining life assessment of an aging urban steam plant, a quality control and welding program for a coastal pulp mill, gas plant integrity inspection, integrity management program reviews for oil sands operators, boiler assessments for a food processor, independent incident investigations and equipment breakdown claim support, and firing-rate trials on a kraft recovery boiler.
Insights
What the incident record says
Analysis built from public failure records and field work. What fails, where, and what the numbers suggest you do about it.
A furnace pressure trip is only as good as its tap
The tap plugs with ash, and a plugged tap does not fail safe. Tap angle, position, line routing, access and the PM that keeps the trip connected.
Audit the bypass register against the field, not the paperwork
Check five safety-critical trips in the field, then open the register. What to look for and what to count.
Where recovery boilers leak: 1,103 BLRBAC incidents, 2001–2026
Twenty-five years of incident reports mapped onto the boiler by location and root cause. Interactive.
Contact
Talk to the inspector, not a dispatcher
Outage planning, a finding you want a second opinion on, a program review before the auditor arrives. Call or write.